@@ -59,9 +59,9 @@
 /* Fixed header pattern */
 header:		.byte	0x00,0xff,0xff,0xff,0xff,0xff,0xff,0x00
 
-mfg_id:		.word	swap16(mfgname2id(MFG_LNX1, MFG_LNX2, MFG_LNX3))
+mfg_id:		.hword	swap16(mfgname2id(MFG_LNX1, MFG_LNX2, MFG_LNX3))
 
-prod_code:	.word	0
+prod_code:	.hword	0
 
 /* Serial number. 32 bits, little endian. */
 serial_number:	.long	SERIAL
@@ -177,7 +177,7 @@ std_vres:	.byte	(XY_RATIO<<6)+VFREQ-60
 
 descriptor1:
 /* Pixel clock in 10 kHz units. (0.-655.35 MHz, little-endian) */
-clock:		.word	CLOCK/10
+clock:		.hword	CLOCK/10
 
 /* Horizontal active pixels 8 lsbits (0-4095) */
 x_act_lsb:	.byte	XPIX&0xff
 
@@ -0,0 +1,111 @@
+Amlogic specific extensions to the Synopsys Designware HDMI Controller
+======================================================================
+
+The Amlogic Meson Synopsys Designware Integration is composed of :
+- A Synopsys DesignWare HDMI Controller IP
+- A TOP control block controlling the Clocks and PHY
+- A custom HDMI PHY in order to convert video to TMDS signal
+ ___________________________________
+|            HDMI TOP               |<= HPD
+|___________________________________|
+|                  |                |
+|  Synopsys HDMI   |   HDMI PHY     |=> TMDS
+|    Controller    |________________|
+|___________________________________|<=> DDC
+
+The HDMI TOP block only supports HPD sensing.
+The Synopsys HDMI Controller interrupt is routed through the
+TOP Block interrupt.
+Communication to the TOP Block and the Synopsys HDMI Controller is done
+via a pair of dedicated addr+read/write registers.
+The HDMI PHY is configured by registers in the HHI register block.
+
+Pixel data arrives in 4:4:4 format from the VENC block and the VPU HDMI mux
+selects either the ENCI encoder for the 576i or 480i formats or the ENCP
+encoder for all the other formats including interlaced HD formats.
+
+The VENC uses a DVI encoder on top of the ENCI or ENCP encoders to generate
+DVI timings for the HDMI controller.
+
+Amlogic Meson GXBB, GXL and GXM SoCs families embeds the Synopsys DesignWare
+HDMI TX IP version 2.01a with HDCP and I2C & S/PDIF
+audio source interfaces.
+
+Required properties:
+- compatible: value should be different for each SoC family as :
+	- GXBB (S905) : "amlogic,meson-gxbb-dw-hdmi"
+	- GXL (S905X, S905D) : "amlogic,meson-gxl-dw-hdmi"
+	- GXM (S912) : "amlogic,meson-gxm-dw-hdmi"
+	followed by the common "amlogic,meson-gx-dw-hdmi"
+- reg: Physical base address and length of the controller's registers.
+- interrupts: The HDMI interrupt number
+- clocks, clock-names : must have the phandles to the HDMI iahb and isfr clocks,
+  and the Amlogic Meson venci clocks as described in
+  Documentation/devicetree/bindings/clock/clock-bindings.txt,
+  the clocks are soc specific, the clock-names should be "iahb", "isfr", "venci"
+- resets, resets-names: must have the phandles to the HDMI apb, glue and phy
+  resets as described in :
+  Documentation/devicetree/bindings/reset/reset.txt,
+  the reset-names should be "hdmitx_apb", "hdmitx", "hdmitx_phy"
+
+Required nodes:
+
+The connections to the HDMI ports are modeled using the OF graph
+bindings specified in Documentation/devicetree/bindings/graph.txt.
+
+The following table lists for each supported model the port number
+corresponding to each HDMI output and input.
+
+		Port 0		Port 1
+-----------------------------------------
+ S905 (GXBB)	VENC Input	TMDS Output
+ S905X (GXL)	VENC Input	TMDS Output
+ S905D (GXL)	VENC Input	TMDS Output
+ S912 (GXM)	VENC Input	TMDS Output
+
+Example:
+
+hdmi-connector {
+	compatible = "hdmi-connector";
+	type = "a";
+
+	port {
+		hdmi_connector_in: endpoint {
+			remote-endpoint = <&hdmi_tx_tmds_out>;
+		};
+	};
+};
+
+hdmi_tx: hdmi-tx@c883a000 {
+	compatible = "amlogic,meson-gxbb-dw-hdmi", "amlogic,meson-gx-dw-hdmi";
+	reg = <0x0 0xc883a000 0x0 0x1c>;
+	interrupts = <GIC_SPI 57 IRQ_TYPE_EDGE_RISING>;
+	resets = <&reset RESET_HDMITX_CAPB3>,
+		 <&reset RESET_HDMI_SYSTEM_RESET>,
+		 <&reset RESET_HDMI_TX>;
+	reset-names = "hdmitx_apb", "hdmitx", "hdmitx_phy";
+	clocks = <&clkc CLKID_HDMI_PCLK>,
+		 <&clkc CLKID_CLK81>,
+		 <&clkc CLKID_GCLK_VENCI_INT0>;
+	clock-names = "isfr", "iahb", "venci";
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	/* VPU VENC Input */
+	hdmi_tx_venc_port: port@0 {
+		reg = <0>;
+
+		hdmi_tx_in: endpoint {
+			remote-endpoint = <&hdmi_tx_out>;
+		};
+	};
+
+	/* TMDS Output */
+	hdmi_tx_tmds_port: port@1 {
+		reg = <1>;
+
+		hdmi_tx_tmds_out: endpoint {
+			remote-endpoint = <&hdmi_connector_in>;
+		};
+	};
+};
@@ -34,6 +34,9 @@ Optional properties for HDMI:
 - hpd-gpios:	The GPIO pin for HDMI hotplug detect (if it doesn't appear
 		  as an interrupt/status bit in the HDMI controller
 		  itself).  See bindings/pinctrl/brcm,bcm2835-gpio.txt
+- dmas:		Should contain one entry pointing to the DMA channel used to
+		transfer audio data
+- dma-names:	Should contain "audio-rx"
 
 Required properties for DPI:
 - compatible:	Should be "brcm,bcm2835-dpi"
 
@@ -0,0 +1,64 @@
+Parallel to LVDS Encoder
+------------------------
+
+This binding supports the parallel to LVDS encoders that don't require any
+configuration.
+
+LVDS is a physical layer specification defined in ANSI/TIA/EIA-644-A. Multiple
+incompatible data link layers have been used over time to transmit image data
+to LVDS panels. This binding targets devices compatible with the following
+specifications only.
+
+[JEIDA] "Digital Interface Standards for Monitor", JEIDA-59-1999, February
+1999 (Version 1.0), Japan Electronic Industry Development Association (JEIDA)
+[LDI] "Open LVDS Display Interface", May 1999 (Version 0.95), National
+Semiconductor
+[VESA] "VESA Notebook Panel Standard", October 2007 (Version 1.0), Video
+Electronics Standards Association (VESA)
+
+Those devices have been marketed under the FPD-Link and FlatLink brand names
+among others.
+
+
+Required properties:
+
+- compatible: Must be "lvds-encoder"
+
+Required nodes:
+
+This device has two video ports. Their connections are modeled using the OF
+graph bindings specified in Documentation/devicetree/bindings/graph.txt.
+
+- Video port 0 for parallel input
+- Video port 1 for LVDS output
+
+
+Example
+-------
+
+lvds-encoder {
+	compatible = "lvds-encoder";
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	ports {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		port@0 {
+			reg = <0>;
+
+			lvds_enc_in: endpoint {
+				remote-endpoint = <&display_out_rgb>;
+			};
+		};
+
+		port@1 {
+			reg = <1>;
+
+			lvds_enc_out: endpoint {
+				remote-endpoint = <&lvds_panel_in>;
+			};
+		};
+	};
+};
@@ -0,0 +1,94 @@
+Drivers for the second video output of the GE B850v3:
+   STDP4028-ge-b850v3-fw bridges (LVDS-DP)
+   STDP2690-ge-b850v3-fw bridges (DP-DP++)
+
+The video processing pipeline on the second output on the GE B850v3:
+
+   Host -> LVDS|--(STDP4028)--|DP -> DP|--(STDP2690)--|DP++ -> Video output
+
+Each bridge has a dedicated flash containing firmware for supporting the custom
+design. The result is that, in this design, neither the STDP4028 nor the
+STDP2690 behave as the stock bridges would. The compatible strings include the
+suffix "-ge-b850v3-fw" to make it clear that the driver is for the bridges with
+the firmware specific for the GE B850v3.
+
+The hardware do not provide control over the video processing pipeline, as the
+two bridges behaves as a single one. The only interfaces exposed by the
+hardware are EDID, HPD, and interrupts.
+
+stdp4028-ge-b850v3-fw required properties:
+  - compatible : "megachips,stdp4028-ge-b850v3-fw"
+  - reg : I2C bus address
+  - interrupt-parent : phandle of the interrupt controller that services
+    interrupts to the device
+  - interrupts : one interrupt should be described here, as in
+    <0 IRQ_TYPE_LEVEL_HIGH>
+  - ports : One input port(reg = <0>) and one output port(reg = <1>)
+
+stdp2690-ge-b850v3-fw required properties:
+    compatible : "megachips,stdp2690-ge-b850v3-fw"
+  - reg : I2C bus address
+  - ports : One input port(reg = <0>) and one output port(reg = <1>)
+
+Example:
+
+&mux2_i2c2 {
+	status = "okay";
+	clock-frequency = <100000>;
+
+	stdp4028@73 {
+		compatible = "megachips,stdp4028-ge-b850v3-fw";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		reg = <0x73>;
+
+		interrupt-parent = <&gpio2>;
+		interrupts = <0 IRQ_TYPE_LEVEL_HIGH>;
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+				stdp4028_in: endpoint {
+					remote-endpoint = <&lvds0_out>;
+				};
+			};
+			port@1 {
+				reg = <1>;
+				stdp4028_out: endpoint {
+					remote-endpoint = <&stdp2690_in>;
+				};
+			};
+		};
+	};
+
+	stdp2690@72 {
+		compatible = "megachips,stdp2690-ge-b850v3-fw";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		reg = <0x72>;
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+				stdp2690_in: endpoint {
+					remote-endpoint = <&stdp4028_out>;
+				};
+			};
+
+			port@1 {
+				reg = <1>;
+				stdp2690_out: endpoint {
+					/* Connector for external display */
+				};
+			};
+		};
+	};
+};
@@ -0,0 +1,75 @@
+Renesas Gen3 DWC HDMI TX Encoder
+================================
+
+The HDMI transmitter is a Synopsys DesignWare HDMI 1.4 TX controller IP
+with a companion PHY IP.
+
+These DT bindings follow the Synopsys DWC HDMI TX bindings defined in
+Documentation/devicetree/bindings/display/bridge/dw_hdmi.txt with the
+following device-specific properties.
+
+
+Required properties:
+
+- compatible : Shall contain one or more of
+  - "renesas,r8a7795-hdmi" for R8A7795 (R-Car H3) compatible HDMI TX
+  - "renesas,rcar-gen3-hdmi" for the generic R-Car Gen3 compatible HDMI TX
+
+    When compatible with generic versions, nodes must list the SoC-specific
+    version corresponding to the platform first, followed by the
+    family-specific version.
+
+- reg: See dw_hdmi.txt.
+- interrupts: HDMI interrupt number
+- clocks: See dw_hdmi.txt.
+- clock-names: Shall contain "iahb" and "isfr" as defined in dw_hdmi.txt.
+- ports: See dw_hdmi.txt. The DWC HDMI shall have one port numbered 0
+  corresponding to the video input of the controller and one port numbered 1
+  corresponding to its HDMI output. Each port shall have a single endpoint.
+
+Optional properties:
+
+- power-domains: Shall reference the power domain that contains the DWC HDMI,
+  if any.
+
+
+Example:
+
+	hdmi0: hdmi0@fead0000 {
+		compatible = "renesas,r8a7795-dw-hdmi";
+		reg = <0 0xfead0000 0 0x10000>;
+		interrupts = <0 389 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&cpg CPG_CORE R8A7795_CLK_S0D4>, <&cpg CPG_MOD 729>;
+		clock-names = "iahb", "isfr";
+		power-domains = <&sysc R8A7795_PD_ALWAYS_ON>;
+		status = "disabled";
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			port@0 {
+				reg = <0>;
+				dw_hdmi0_in: endpoint {
+					remote-endpoint = <&du_out_hdmi0>;
+				};
+			};
+			port@1 {
+				reg = <1>;
+				rcar_dw_hdmi0_out: endpoint {
+					remote-endpoint = <&hdmi0_con>;
+				};
+			};
+		};
+	};
+
+	hdmi0-out {
+		compatible = "hdmi-connector";
+		label = "HDMI0 OUT";
+		type = "a";
+
+		port {
+			hdmi0_con: endpoint {
+				remote-endpoint = <&rcar_dw_hdmi0_out>;
+			};
+		};
+	};